Back to Videos
Video: Wind Farm Design - Q&A - Moving Pad Locations
Updated September 19, 2025
This article applies to:
- RoadEng Civil
Road & Corridor Design Videos
- Road & Corridor Design Videos
- Video: 5-Minute Road Design | Forestry Road from LiDAR
- Video: Designing a Road with Full Bench Cut (End Haul Road)
- Video: Simple Entrance (Driveway) Intersection Design
- Video: Curve Widening
- Video: How to Fillet an Intersection
- Video: Shading and Display Reporting
- Video: Mass Haul Diagram
- Video: Working with Multiple Horizontal Alignments & Project Explorer Panel
- Video: Working with the Opti Haul Graphic and Smart Pits
- Video: Horizontal Alignments and Reference Features
- Video: Ditch Profiling Using a Reference Alignment
- Video: Creating an Independent Ditch Profile
- Video: As-Builts - Calculating Volumes & Cross-Sections
- Video: RoadEng for Wind Farm Road Design | 1-Minute Tour
- Video: Culvert Replacement Project Using Corridor Surfaces
- Video: Importing LandXML Files
- Video: Curve Widening in RoadEng
- Video: Tapering Cross-Section Templates in RoadEng
- Video: Accounting for Stripping Material Adjacent to a Road Design
- Video: Assigning an Independent Subsurface Layer to a RoadEng Location Project
- Video: Y Intersection Design using RoadEng
- Video: Culvert Editor Panel
- Video: Exporting LandXML from RoadEng
- Video: Adding An Alignment from Another RoadEng Project
- Video: Creating Road Turnouts with Overrides in RoadEng
- Video: Designing a A Culvert with a Headwall in RoadEng
- Video: How to Share an Avenza Zip File Created in RoadEng
- Video: Creating Construction Document with RoadEng | 9-minute Multi-Plot Intro
- Video: Including a Rockfill Template in your RoadEng Design
- Video: Calculating As-Built Quantities
- Video: Working with the Wall III Component in RoadEng
- Video: Strategies for Extending your Topo Surface
- Video: Pad IV – Windfarm-specific cross section template.
- Video: Mass Haul in RoadEng
- Video: Assigning stripping and clearing in RoadEng's Location module
- Video: GRS/MSE Wall Template Component - RoadEng Version 11
- Video: How to show an existing culverts as a reference feature
- Video: Customizing Page Sizes In RoadEng's Multi-Plot
- Video: Working with Slope XX - Buttressed Cut Slope - Template Component in RoadEng
- Video: 5 min Road Realignment Using LiDAR
- Video: Merging A Road Design Back Into the Original Ground (Topo)
- Video: RoadEng Template for Rail Bed and Track Design
- Video: Reporting Cut and Fill Volumes
- Video: Hydrology Tools - V11 Preview
- Video: Correcting Magnetic Declination
- Video: Report Points in RoadEng
- Video: Designing & Optimizing a Road Project (in 12 minutes)
- Video: How to Add Rolling Dips in RoadEng
- Video: Culvert Positioning with "Attach to Ditch"
- Video: Understanding Input Parameters for Hydrology Tools
- Video: What is Represented by the Watershed Graphic?
- Video: Exporting a Design Surface to HEC RAS using RoadEng
- Video: Adding and Changing P-Lines in RoadEng
- Video: Defining a Polygon Rectangle for Thinning Large Resolution Data Sets
- Webinar: Efficient and Sustainable Trail Design with RoadEng
- Video: Cut & Fill Display Shading in RoadEng
- Video: Calculating As-Built Volumes (Part 2): Road Volumes for Multiple Layers
- Video: Calculating As-Built Volumes 3 Ways
- Video: Calculating As-Built Volumes (Part 3): Visual Comparison Between Design & As-built Surfaces
- Video: Creating a Typical Section in Multi-plot
- Video: Introduction to Earthwork Optimization for Road Design
- Video: Wind Farm Design - Q&A - Moving Pad Locations
- Video: Wind Farm Design - Q&A - Improving the Shape of Reference Pads in Location
- Video: Wind Farm Design - Q&A - Is Data exchange with QGIS/AutoCAD possible?
- Video: Wind Farm Design - Q&A – How long of a road can you optimize vertically?
- Terrain Modelling & Data Import Videos
- Site Design Videos
- Export & Output Videos
- Getting Started Videos
- Webinars